quality
individual
solutions
Greentec Cheetah 30/13 wood chipper combination
80 – 200 HP
30 cm
12 – 22 mm
app. 7200 kg
- GCS – Greentec Control System.
- Own hydraulic cooling system (using airstream of blades of disc).
- Less power needed because the infeed is at an angle.
- Milled disc: disc is even sunken towards the next blade.
- All machines are manufactured out of premium steel 355 (52-3).
2 agressive infeed rollers.
Infeedfunnel with unique slots at the bottom: sand, soil and gravel will damage the blades less, meaning longivity of the blades (when cranefed)
Optimum cutting angle.
GCS
Greentec Control System
High tipper
Options
- Combi infeed table for hand infeed and crane feed
- High tipping bunker 13m3 left tipping
- Multi joystick control for crane and chipper together with GCS control, including electronic proportional valve
- Hydraulic lift axle operated by the tractor’s single-acting hydraulic valve (CH30 / 8)
- Hydraulic or air brake
- Also possible with TÜV inspection or PVG inspection
- Infeedroller hydraulically opened
- Actionboarding
- Camera
- LED-lighting around according to guidelines, led flash lights, flashing light
- Tool carrier
Combi infeed table for hand infeed and crane feed
Radio remote control for crane and chipper
Actionboarding
Also left-tilting possible.
Features |
| Woodchipper |
| Own hydraulic cooling system (using airstream of blades of disc) |
| 2 agressive infeed rollers both independently driven |
| Infeed on three sides fitted with anvilknives, making it easy to adjust for right chip length, even after many working hours. |
| Less power needed because the infeed is at an angle |
| Chipper disc |
| Milled disc: disc is even sunken towards the next blade resulting in high infeed speed with minimal resistance |
| Quality |
| All machines are manufactured out of premium steel 355 (52-3) |
| Discharge chute, bottom beneath disc equipped with replacable wear plate made of hardwearing Hardox steel |
| After sandblasting machines are double powder coated |
| Machines are made of durable materials, including bearings, hydraulic valves, engines, pumps and more |
| Servicing |
| Knives are easy accessible when the infeed rollers are hydraulically positioned above the machine |
| Disc is easy to lock for chaging the knives |
| Hinged lid over rollers, underneath grease points are easy to reach |
| Anvil knife adjustable, and can be used twice |
Technical Specifications | |
| Infeed opening (mm) | 300 x 580 |
| Feed opening channel (mm) | 300 x 320 |
| Disc (mm) | Ø 960 x 58 |
| Anvil knives | 3 |
| Max. chip length (mm) | 22 |
| Drive | PTO 540E/1000/1000E |
| Revolutions disc (rpm) | 750 /850/1000 |
| Number of knives on disc | 2 |
| Infeed speed (m/s) | 0,6 |
| Capacity up to (m3/hour) | 40 |
| Gear casing full oilbath bearing | |
| Power requirements (HP) | |
| from 80-140 hp | 540eco/1000 rpm pto and 750 rpm disc |
| from 100-200 hp | 1000/1000eco rpm pto and 1000 rpm disc |
| Container Volume (m3) | 13 |
| Gross weight max. (tonnes) (k80) | 20 |
| Loading capacity tandem axle (tonnes) | 16 |
| Steel toolbox on both sides, with lock and key |
| Infeedroller hydraulically opened |
| Cheetah 30-13 chute, hydraulic slewing & manual deflector adjustment |
| Air brakes, 2 air ducts VC13 |
GCS control – Greentec Control System
- Compact touchscreen control.
- Programs for different wood types.
- In these programs different parameters are adaptable. Pressure down at top roller, starting and stopping speed of the no stress, either or not reversing of the infeed rollers and infeed speed.
- Easy switch to low engine speed to reduce fuel consumption and noise. This gives coarse wood chips with even lower fine percentage.
- Chip size and wood type adjustable at any time.
- Stopping and if needed short reversing of the infeed responds not only to speed, but also to working pressure of the system.
- GCS control box compact design with stainless steel casing.
- Vulcanised controllers without moving parts, less chance of error.
- In these programs different parameters are adaptable. Pressure down at top roller, starting and stopping speed of the no stress, either or not reversing of the infeed rollers and infeed speed.
- Exclusive on Ufkes Greentec machines.
- Least possible electronics (relay, cables and more), operational reliability.
- Minimum cables on the machine, only Canbus signal with plus and minus.
- Minimal chance of errors
- Waterproof up to IP67.
- 5 languages available; Dutch/English/French/German/Polish.
“Unique system, only with Greentec machines”
