quality
individual
solutions
Greentec Cheetah 30 compact Unimog
< 300 hp
30 cm
12 – 22 mm
app. 2450 kg (incl. crane)
- Less power needed because the infeed is at an angle
- Milled disc: disc is even sunken towards the next blade resulting in high infeed speed with minimal resistance
- All machines are manufactured out of premium steel 355 (52-3)
- Easy to maintain
Fitted as standard
- Infeedroller hydraulically opened
- Unimog mounting system and integrated crane platform with hydraulic support leg
Official UnimogPartner
2 agressive infeed rollers.
Optimum cutting angle, less power and less fuel.
Infeedfunnel with unique slots at the bottom: sand, soil and gravel will damage the blades less, meaning longivity of the blades (when cranefed)
Options
- Tipper 8 m3 rear tipper for Unimog mounting
- Remote control
- Combi hand infeed and crane feed, hydr. raisable instead, hydraulic raisable
- Crane and crane control
- Camera – complete fitted incl. separately supplied screen
- Uncoupling frame fitted with 2 tubes for forklift spoons for easy dismantling and storage of the machine
- Special colour
Combi hand infeed and crane feed, hydr. raisable instead, hydraulic raisable
Greentec Control System
Radio remote control for crane and chipper
Features |
| Woodchipper |
| Own hydraulic cooling system (using airstream of blades of disc) |
| 2 agressive infeed rollers both independently driven |
| Infeed on three sides fitted with anvilknives, making it easy to adjust for right chip length, even after many working hours. |
| Less power needed because the infeed is at an angle |
| Chipper disc |
| Milled disc: disc is even sunken towards the next blade resulting in high infeed speed with minimal resistance |
| Quality |
| All machines are manufactured out of premium steel 355 (52-3) |
| Discharge chute, bottom beneath disc equipped with replacable wear plate made of hardwearing Hardox steel |
| After sandblasting machines are double powder coated |
| Machines are made of durable materials, including bearings, hydraulic valves, engines, pumps and more |
| Servicing |
| Knives are easy accessible when the infeed rollers are hydraulically positioned above the machine |
| Disc is easy to lock for chaging the knives |
| Hinged lid over rollers, underneath grease points are easy to reach |
| Anvil knife adjustable, and can be used twice |
Technical Specifications | |
| Infeed opening (mm) | 300 x 580 |
| Feed opening channel (mm) | 300 x 320 |
| Disc (mm) | Ø 960 x 58 |
| Anvil knives | 3 |
| Max. chip length (mm) | 22 |
| Drive | PTO 1000 |
| Revolutions disc (rpm) | 1000 |
| Number of knives on disc | 2 |
| Infeed speed (m/s) | 0,6 |
| Capacity up to (m3/hour) | 40 |
| Power requirements (HP) | < 300 |
| Infeedroller hydraulically opened |
| Own hydraulic system |
| Drive-off safety when support legs are lowered |
| Type C chute, hydraulic; slewing, up and down, deflector adjustment |
| Unimog mounting system and integrated crane platform with 2 hydraulic support legs |
| Suitable as of U427 |
| Required options Unimog: Ca4,N08, HN3 oder HN6 oder HN8 oder HN9,TS2 oder TS3, P60/PB6 oder PB8, 12 Volt connection in cab |
| Uncoupling frame with 3 castors for easy dismantling of the machine |
| Driver sits on the left for best visibility |
| If necessary, additional inspection, due to restricted field of vision, at subsequent cost. |
