This completely new version of the Jaguar 40 series comes on rubber tracks with high ground clearance. This makes hard-to-reach areas, terrain with lots of stubbles and wet areas accessible for work without damaging the ground. The machine is easy to operate with remote control. A 140 hp Stage V Doosan engine ensures maximum capacity from this compact machine. As an option, the machine can be fitted with a slewing ring (270°). The infeed can be turned quickly and easily to the material to be chipped. Also the machine can be equipped with a telescopic woodcrane, a closed infeed chain to allow easy feeding of residual material and a winch to pull the wood towards the machine.
140 HP
40 cm
4500 kg
Fitted as standard
- GCS 1.1 control
- Pipe, hydraulic up and down, hydraulic chip deflector.
- Integrated blowing system which, in combination with Venturi blowing system guarantees a powerfull airstream.
Integrated blowing system which, in combination with Venturi blowing system guarantees a powerfull airstream.
red = powerfull airstream
blue = under pressure/vacuum
yellow = snippers
Upper feed roller internally driven by a heavy poclain motor.
Track length total 2000 mm, width rubber track 300mm
Knives are easy accessible, under a hinged cover, on the top of the machine.
Remote control (GCS1.1)
Options
- With slewing ring, machine can be turned hydraulically
- TG62T telescopic wood crane
- Closed infeedchain covering complete width of the infeedtable. Only for crane infeed
Closed infeedchain
Hydraulic tilting Venturi
Features |
| Woodchipper |
| Own hydraulic cooling system (using Venturi airflow) |
| Integrated blowing system which, in combination with Venturi blowing system guarantees a powerfull airstream |
| No nonsense machine; chipping at the front, discharge at the back. |
| No jacks or accelarator needed, which otherwise shatters good woodchips. |
| This prevents unneccassary wear, saves power and therefore fuel, resulting in higher efficiency |
| Drum |
| (Quick-change) Knives distributed along the drum. Drum with blower blades on both sides. |
| Widia bottom knive placed below cutting knive, easy accessible |
| Exterior wall of drum is 20 mm thick and main axe Ø70 mm |
| Specially designed anvil knife, small branches are cut at a differente angle, resulting in better chipping quality. |
| Infeed |
| Upper infeed roller internally driven by heavy, low maintenance Poclain engines, therefore no open slits besides the infeed, preventing chips from scattering |
| Screenunit |
| Easy replacing of the screen at the side of the machine. Possible to chip without screen. |
| Quality |
| All machines are manufactured out of premium steel 355 (52-3) |
| Discharge chute, bottom between infeed roller and anvil knife beneath the drum equipped with replacable wear plate made of hardwearing Hardox steel |
| Machines are made of durable materials, including bearings, hydraulic valves, engines, pumps and more |
| After sandblasting machines are double powder coated |
| Servicing |
| Knives are easy accessible, under a hinged cover, on the top of the machine. |
| Drum is easily secured for changing knives. |
| Anvil knife adjustable, and can be used four times |
Technical Specifications | |
| Infeed opening (mm) | 400 x 600 |
| Feed opening channel (mm) | 420 x 600 |
| Max. infeed softwood (mm) | Ø 400 |
| Drum (mm) | Ø 600 x 600 |
| Top roller (mm) | Ø 430 |
| Chipper knives | 4 |
| Anvil knives | 1 |
| Max. chip length (mm) | 20 |
| Specifications Track |
| Track length total 2000 mm, width rubber track 300mm. |
| Drive 4200 Nm. |
| Rubber tracks |
| 3-speed, with integrated negative brake |
| 6, Motor |
| Electrical start |
| Ad-Blue |
| manual clutch |
| Oil cooler (hydraulic) |
| Control |
| Remote control (GCS1.1) for chipperfunctions 30/40 Track<br /> – Deflector adjustment<br /> – Chute rotation<br /> – Chute up/down<br /> – In/outfeed<br /> – Roll open<br /> – Engine up/down<br /> – Forwards/ backwards<br /> – Hi/low/ creep |
| Cable control tracks (coming home). (GCS1.1) |
| Combi hand infeed and crane feed, hydraulic raisable |
| Type C chute, hydraulic; slewing, up and down, deflector adjustment |
GCS control – Greentec Control System
- Compact touchscreen control.
- Programs for different wood types.
- In these programs different parameters are adaptable. Pressure down at top roller, starting and stopping speed of the no stress, either or not reversing of the infeed rollers and infeed speed.
- Easy switch to low engine speed to reduce fuel consumption and noise. This gives coarse wood chips with even lower fine percentage.
- Chip size and wood type adjustable at any time.
- Stopping and if needed short reversing of the infeed responds not only to speed, but also to working pressure of the system.
- GCS control box compact design with stainless steel casing.
- Vulcanised controllers without moving parts, less chance of error.
- In these programs different parameters are adaptable. Pressure down at top roller, starting and stopping speed of the no stress, either or not reversing of the infeed rollers and infeed speed.
- Exclusive on Ufkes Greentec machines.
- Least possible electronics (relay, cables and more), operational reliability.
- Minimum cables on the machine, only Canbus signal with plus and minus.
- Minimal chance of errors
- Waterproof up to IP67.
- 5 languages available; Dutch/English/French/German/Polish.
“Unique system, only with Greentec machines”
