200 – 450 HP
65 cm
Fitted as standard
- GCS control
- Combinationpipe, hydraulic up and down, electric chip deflector
- Venturi discharge chute can be tilted hydraulically, for easy replacing of the sieve unit
- Lowered table for bottom roller providing more space for wood clamp to insert thick logs
- Integrated blowing system which, in combination with Venturi blowing system guarantees a powerfull airstream
Integrated blowing system which, in combination with Venturi blowing system guarantees a powerfull airstream.
red = powerfull airstream
blue = under pressure/vacuum
yellow = snippers
high tipper
Upper feed roller internally driven by a heavy poclain motor.
(Quick-change) Knives are easy accessible when the infeed rollers are hydraulically positioned above the machine, giving direct view of knive and anvil knife
Venturi discharge chute can be tilted hydraulically, for easy replacing of the sieve unit.
Options
- Remote control for operating chipper
- Electric start aid 12 volt including cable set
- Different crane and crane control options
- Chassis Air brakes instead of hydraulic brakes
- Different options for slow traffic
- Different lighting and support leg wheel set options
Versions
- Available with 3 or 5 feed rollers
- Capacity 20 m3 or 25 m3
- Standard or telescopic high tipper
Standing input roles
Various crane and crane control options.
Action board
Features |
| Woodchipper |
| Own hydraulic cooling system (using Venturi airflow) |
| Integrated blowing system which, in combination with Venturi blowing system guarantees a powerfull airstream |
| No nonsense machine; chipping at the front, discharge at the back. |
| No jacks or accelarator needed, which otherwise shatters good woodchips. |
| This prevents unneccassary wear, saves power and therefore fuel, resulting in higher efficiency |
| Greentec drum woodchippers stand for uniform chips with low particulate percentage |
| Drum |
| (Quick-change) Knives distributed along the drum. Drum with blower blades on both sides. |
| Widia bottom knive placed below cutting knive, easy accessible |
| Exterior wall of drum is 40 mm thick and main axe Ø125 mm |
| Specially designed anvil knife, small branches are cut at a differente angle, resulting in better chipping quality. |
| Infeed |
| Lowered table for bottom roller providing more space for wood clamp to insert thick logs |
| Smaller top roller with minimal distance to drum, |
| Upper two infeed rolls internally driven by heavy, low maintenance Poclain engines, therefore no open slits besides the infeed, preventing chips from scattering |
| Bottom roller driven by heavy Poclain wheelengine |
| With the electronic adjustable piston pump and a working pressure of max. 350 bar there is maximum infeedcapacity |
| and minimal heat generation of the oil |
| Infeed speed always parallel to speed drum, and easy electronically adjustable |
| Screenunit |
| Venturi discharge chute can be tilted hydraulically, for easy replacing of the sieve unit |
| Quality |
| All machines are manufactured out of premium steel 355 (52-3) |
| Teeth on infeed rollers are made of hardwearing Hardox steel, guaranteeing agressive infeed for years |
| Discharge chute, bottom between infeed roller and anvil knife beneath the drum equipped with replacable wear plate made of hardwearing Hardox steel |
| Machines are made of durable materials, including bearings, hydraulic valves, engines, pumps and more |
| After sandblasting machines are double powder coated |
| Servicing |
| (Quick-change) Knives are easy accessible when the infeed rollers are hydraulically positioned above the machine, giving direct view of knive and anvil knife |
| Drum is easily secured for changing knives. |
| Changing a knive takes about 5-10 min |
| Anvil knife adjustable, and can be used twice |
Technical Specifications | 3-infeed rollers |
| Infeed opening (mm) | 750 x 1450 |
| Feed opening channel (mm) | 650 x 920 |
| Max. infeed hardwood (mm) | Ø 400 |
| Max. infeed softwood (mm) | Ø 650 |
| Drum (mm) | Ø 960 x 930 |
| Top roller (mm) | Ø 350 |
| Bottom roller (mm) | Ø 300 |
| Chipper knives | 6 |
| Anvil knives | 1 |
| Max. chip length (mm) | 34 |
| Gross weight max. (tonnes) (k80) | 28 |
| Loading capacity tandem axle (tonnes) | 24 |
| Power requirements (HP) | 200 – 450 |
| Capacity up to (m3/hour) | 165 |
| Towbar height according to drawing |
| Hydraulic support leg rear |
| LED-lighting around according to guidelines |
| 7-pole light connection |
| Steel toolbox on both sides, with lock and key |
| Low maintenance oil cooled overrun clutch integrated in pulley |
| Greentec Control System 3.0 box with touchscreen, to be placed in cab |
| Hydraulic tilting Venturi discharge funnel 962 |
| Air brakes, 2 air ducts VC20 |
| Ball head coupling K80 |
GCS control – Greentec Control System
- Compact touchscreen control.
- Programs for different wood types.
- In these programs different parameters are adaptable. Pressure down at top roller, starting and stopping speed of the no stress, either or not reversing of the infeed rollers and infeed speed.
- Easy switch to low engine speed to reduce fuel consumption and noise. This gives coarse wood chips with even lower fine percentage.
- Chip size and wood type adjustable at any time.
- Stopping and if needed short reversing of the infeed responds not only to speed, but also to working pressure of the system.
- GCS control box compact design with stainless steel casing.
- Vulcanised controllers without moving parts, less chance of error.
- In these programs different parameters are adaptable. Pressure down at top roller, starting and stopping speed of the no stress, either or not reversing of the infeed rollers and infeed speed.
- Exclusive on Ufkes Greentec machines.
- Least possible electronics (relay, cables and more), operational reliability.
- Minimum cables on the machine, only Canbus signal with plus and minus.
- Minimal chance of errors
- Waterproof up to IP67.
- 5 languages available; Dutch/English/French/German/Polish.
“Unique system, only with Greentec machines”
